Agricultural accessories

Product

undefined

undefined

News

undefined

undefined

Diagnosis and elimination of agricultural machinery faults

The diagnosis and troubleshooting of agricultural mach₹inery faults is relatively difficult. Some maintenance ✘personnel have always used the method of replacement testing, regardless of the large or small par∏ts, as long as they believe that the components that may cause the fault are replaced one by  one, the results not only fail to eliminate the fa ult, but also replace the parts that should not be replaced at will, increasing the expense✘s of agricultural machinery users. Some faulty componεents can be completely restored to their technical perfoγrmance through repair, without the need for complex repair processes.  However, maintenance personnel require users to replace them with new par₹ts and blindly adopt the "replacement repair" method, resulting in ser↕ious waste. The practice of blindly replacing parts and blindly re✘placing repairable parts mentioned above still exists to varying degrees‍ in some repair units. During maintenance, the cause a>nd location of the fault should be carefully analyzed and judged based on the fault phenome"non. For repairable components, repair methods should be adopted to restore technical perfoπrmance, and blind replacement of components should be avoided. Failure to check the quality of λnew parts after assembly is a common issue Before replacing thφe parts, some maintenance personnel do not conduct technical inspections on the new part s and install them directly on agricultural machin¶ery. This approach is unscientific. At present, the quality of agricultu☆ral machinery spare parts sold in the market is uneven, with ★some counterfeit and inferior parts being mixed up; There are also some access ories whose performance changes due to long invent¥ory times, such as not being tested, which often cause malfunctions after assembly. B<efore replacing with new accessories, it is necessary t×o conduct necessary inspections and tests, including appearance and performance tests, to ensu re that the new accessories are faultless and prevent unnecessary trouble cause₩d by them.

隐藏域元素占位

undefined

undefined

Correct procedures for using grass grabbing machines

Correct procedures for using grass grabbing machines: 1. Drivers must undeπrgo technical training to familiarize themselves with the performance♣, construction, operation, and maintenance of loaders and grass grab<bers. 2. It is strictly prohibited for drivers who are drunk or have mental disorders to operate‍ the machine, and it is strictly prohibited to drive with illness or fatigue‌. 3. During driving operations, drivers need to concentrate and not look left or right. They shoul¶d pay attention to the direction of travel and those working $around them, and sound the horn to warn when there is danger. 4. During driving operations, pass↕engers in the driver's cab are not allowed to overload, and passeng±ers are strictly prohibited from other parts. 5. Before and after  daily operations, a walkaround inspection is required to ensureδ the guarantee of operations. 6. Before starting, check the conditiλon of fuel, cold water, lubricating oil, and hydraulic oil. If there is a leak, promptly handle i₹t, and if there is a lack, adjust and supplement it in a timely manner. 7. Check if all connectβing parts are worn or loose. Check if the tire pressure meetφs the regulations. Check the tension of the fan belt and check the air filter indicator. ∞8. Check whether the lighting, instruments, horns, and other components are normal. 9. The$ engine should not start for more than 5 seconds each time. If one start is unsucce↓ssful, it must wait for 30 seconds before starting again. If three starts ar​e unsuccessful, the cause should be checked and the fault should be resolved≥ before starting again. 10. After starting, idle and idle the enγgine to check if all instruments are normal. If there are any abnormalities, stop the engi₽ne immediately to check the cause. The driver can onl♣y operate when the buzzer "beeps" and disappears wi∏thout any abnormal vibration, noise, or odor. 11. Before operati✘on, test the equipment and check if the steering, braking, and working systems are sensitive. 12.→ During driving, it is necessary to regularly pay attention to whether the index of each instr ument meets the specified requirements. 13. When traveling, place the bγucket at a height of about 0.5m above the ground; Do not lift the bucket∏ too high to transport materials; Do not lift the b♦ucket while driving. 14. When working on slopes or cros sing obstacles such as ditches, slow down, make small↕ corners, and be careful not to tip over. Advance uphill and retreat downhi₽ll.

隐藏域元素占位